Sveiki,
pasidalinsiu info apie atsarginio avensio uzvedimo raktelio padarymo subtilybes. Kadangi, kai pirkau savaji avensi buvo tik vienas raktelis, tad norejau pasigaminti atsargini. Atstovybe paprase 471,80 Lt su PVM, todel sumasciau geriau pasigooglinti ir pasigaminti pats.
Zodziu parsisiunciau is ebay naudota rakta (110lt manau galima rasti ir pigiau bet kiek ieskojau visi srotai pardavineja su imobilaizerio deze ir nori daugiau pinigu). Taip pat is ebay parsisiunciau nauja tuscia neispjauta rakta ~50lt (jei kas ieskosit tai atsargiai, nes ju yra daug skirtingu rusiu) Ispjovimas kainavo 10lt. Zodziu sumoj raktas gavosi 170lt. Toliau reikejo rakta uzsiprogramuot cia galite pasiskaityt kaip tai daroma:
http://www.toyotaownersclub.com/forums/index.php?showtopic=62528&hl=key+programmingO trumpai tai programavimo principas toks:
Reikia istrinti is atminties senus raktus (kazkodel man neistrynus senu naujo nepririso):
You can erase all the keys and start over by turning a working master key 6 times and then opening and closing the door 7 times. Then remove the key and reprogram again.
Naujo rakto imobilaizerio pririsimas:
STEPS:
1. Begin by sitting in the driver seat with all the doors shut.
2. Insert your working master (black) key in the ignition.
3. Very Quickly, turn the key from "LOCK" to "ON" 5 times. (You will end with the key in the "LOCK" position)
4. Immediately, open and close the driver door 6 times very quickly. (End with the door closed)
5. Immediately, remove your working Master key and insert your new Master Key
6. Turn the key to the "ON" position and leave it there while you wait for 1 minute.
7. After the minute, if you want to program another key, just remove the first one and insert the next one, turning it to "ON" and leaving it in position for 1 minute.
8. When you are through programming keys, just take the last one out, open and then close the driver door to lock in the programming, and your done
Mygtuku funkcionalumo aktyvavimas:
1) Make sure that the key is not in the ignition, the doors are unlocked, and the driver's door is open.
2) Very quickly, without turning, insert and remove key from the ignition twice. (leave key out)
3) Close and open the driver door twice. (leave door in open position)
4) Again, insert key into the ignition and remove it. This time only once. (leave key out)
5) Close and open the driver door twice, then close the door.
6) Insert key into the ignition and leave it in the LOCK position.
A. Add mode:
A1) Turn the key to "ON" for 1 second, then turn back to "LOCK".
A2) Remove the key.
A3) You’ll hear the doors "LOCK" and 1 second later "UNLOCK" (just listen)
A4) On your remote, press the lock and unlock buttons simultaneously for 1 to 1½ seconds, then let go.
A5) On your remote, IMMEDIATELY press unlock by itself.
A6) You’ll get one of three responses:
R1) You’ll hear the doors "LOCK", then "UNLOCK" once. The remote is accepted. If you want to program another remote, immediately proceed to step A4 with your second remote, otherwise open the driver’s door and the remote is registered.
R2) You’ll hear the doors "LOCK", then "UNLOCK" twice. Either you didn’t use the same remote in steps A4 and A5(not likely), or this remote was already registered.
The timing was off when you pressed the LOCK and UNLOCK buttons simultaneously and then UNLOCK by itself. Immediately press the two buttons together and the unlock by itself again. Keep trying until you get the locks to signal once that you have been successful. Then if you have another remote to program, quickly press its' buttons as before, until you hear the locks signal once. When you are finished, open and close the driver door to lock in the programming.
R3) If no response, go back to step 1 near the beginning of these instructions.
Viska atlikus teisingai raktas vekia